m_m_のブログ一覧

新しいピカソについての書き込みをされてる方がおられたので、ネタ元をさがしてみました。

なんだか、普通のクルマになった感じですね。
前から目撃されてるのと変わってないから
これがほぼ最終形なのでしょうか。

この写真はショートだと思いますが、
そういえば、グランドピカソの写真は
まだ出てないですね。

これが、リアミラーです。

Gentaさんが紹介されてたミラー内蔵カメラを
Citroen Service のパーツリストで確認してみました。

確かに日本向けに着けてる様ですね。
日本向けのピカソは、イギリス向けのものを
日本向けとして持って来てるのかと思ってましたが、
ちゃんと日本向けってのがあるんですね。
そして、このカメラは無線で飛ばしている？!
ヘテロダインって無線の事でしょうか？

リアミラーの内蔵モニタは、日本向けだけでは
ないからか、JAPAN の表記は、特に何も記載が
無いですが、こちらにもスーパーヘテロダイン
って書いてあるので、無線なのかな。

無線だったら、ピカソのリアミラーと交換して、画像映せたり出来るのかな。

この記事は、PCJの企業努力による日本仕様のDS5について書いています。

ランボルギーニのスマホが発売されるらしいです。

さて、そのお値段とは？？

Tod さんから、早速お返事が来ました。
あなたの車とはペアになってないよ。って。
まぁ車がないから、ペアになる訳もないですよね。
そして、とりあえず違う車種を選んでみてね。ということかな。
という事は、別に車種情報が無くても情報は見られる様ですね。

結局、相手側のアダプタと接続されていないので、画面イメージを確認する事は出来ませんでした。

どなたか着けてみられませんか？？

Tod Hamilton, Jun 13 12:38 (EDT):
m.k,
The log file indicates that you are not paired. What year is your vehicle? You will need to try a different vehicle if you can.I am sending the steps to try.
m.k,

Basics:
The BT1 is designed for quickly connecting to the Bluetooth device with which it was last paired. If you are changing Apple devices, you will need to un-pair (forget) the first device before you can pair with the new device.
When the BT1 is plugged into the OBDII port, you will see the red LED. This indicates that there is power on the OBDII port. (for NO red LED refer to C) below)
The engine must be running (the BT radio powers on when the engine is running):
When you see the blue LED, it will blink slowly, blink fast or be on steady.
Slow: BT1 is pair-able and searching.
Fast: BT1 is attempting to connect to the last known device.
Steady: BT1 has connected and is ready to use.
If issues continue, send us the make/model/year of your vehicle and try a different vehicle if you can.

I'm sorry you are having connection issues. Please follow the steps below to get your BT1 up and running.

1) Plug-in the BT1 to the OBD-II connector in your vehicle. The connector is located on the driver’s-side of the vehicle and is usually under the dash. The connector may also be behind a small trim door or plate.

2) Start your vehicle and wait for the BT1 to beep. This indicates that the BT1 is ready to go.

3) The BT1 pairs with your phone just like a Bluetooth headset. Open “Settings” on your device, then “General” and “Bluetooth.” If Bluetooth is OFF, turn it ON. Your device will now search for the BT1.

4) When you see “GoPoint BT1” on the screen, tap it to pair with it.

5) Wait until the Devices list shows that the GoPoint BT1 is connected.

6) Follow the on-screen directions to get the App from the iTunes App Store if you don’t already have it.

7) If you already have an App installed, you will need to wait for the BT1 to beep and connect to your device before you begin using the software. Look for the Bluetooth icon to be lit at the top of your screen.


If your BT1 is still not working, try the following:

A) iOS RESET:

Resetting your device does not erase any information; it’s just like re-booting your home PC.

• Press-and-hold the Home button (front bottom of the screen) and the Sleep/Wake button (on top) simultaneously.
• Continue holding both buttons (IGNORE the “Slide to power off”) until the Apple logo appears on your screen.
• Let go when the Apple logo appears.
• Allow your device to restart.

Re-do steps 1-7 above.

B) Power down and restart:

Power down your iPhone/iPod/iPad and restart it. Re-do steps 1-7 above.

C) Vehicle electrical Issues:

The BT1 cable requires power from the vehicle to operate. This power comes from the 16-pin vehicle diagnostic connector that the GL1 cable plugs into. Sometimes the fuse for this circuit is blown. Check the fuses, especially the fuse for the cigarette lighter circuit, to be sure that you have power on the connector. If you have access to a multi-meter, you can check for voltage across pins. You can reference the pins here: https://en.wikipedia.org/wiki/On-board_diagnostics#OBD-II_Diagnostic_connector.
Best regards,

Tod Hamilton
GoPoint Technology Support Team

Why has GoPoint Technology declared war on the check engine light?
http://gopointtech.com/our-story/

Friend us on Facebook: http://www.facebook.com/pages/Rochester-Hills-MI/GoPoint-Technology-Inc/157901226197

Follow us on Twitter: https://twitter.com/gopointtech

Join our Email: http://visitor.r20.constantcontact.com/d.jsp?llr=hxiyfhdab&p=oi&m=1102973772519


m.k, Jun 13 12:15 (EDT):
I'm having a problem with...

My car is Citroen C4 Picasso.
But this tool is not supported MyCar.
How can I have support it.

Model: iPhone

OS: iPhone OS

OS Version: 5.1.1

BT1: 1.0.2


Sent from my iPhone

GoPointLog.log

Attachment(s)
GoPointLog.log
This email is a service from GoPoint Technology