This has to be one of the finest Exomotive Exocet builds to date. Roman Maguinez of
Blackbox Motorsports (the same guy who was selling the Mazdaspeed C-Spec motor) is now offering this spectacular kit car for sale. Based on Mazda Miata running gear, the Exocet uses a custom steel spaceframe chassis. Without any bodywork, it is reminiscent of the Ariel Atom and it is much lighter than a stock Mazda Miata. These cars are infinitely customizable and this example is a top flight build using only the best of the best components available.
Exomotive Exocet Sport kit (purchased Mar. '14):
- Additional passenger diagonal roll bar bracing
- Wing mount kit for CoT wing setup
- Domex shock spacer mounts
- "80% chrome" chassis coating and "fine textured wrinkle black" aluminum panel finishing from Industrial Powder Coatings
- M6 nut-sert fasteners for quick transmission tunnel removal with nickel plated Grade-8 hardware
Donor components from 2000 Mazda Miata:
- Subframes, control arms, uprights, and steering rack
- Electronics and wiring harness
- Fuel tank assembly
- Pedal box and steering column
- Brake and clutch hydraulic assemblies
Engine:
- Mazda BP5A 1.8L Japanese engine
- Jackson Racing Rotrex C30-74 supercharger
- BP5A ECU with Jackson Racing fuel management (tuned @ Church's Automotive Testing)
- Deatschwerks DW200 fuel pump
- Denso 280cc injectors flow tested at RC Engineering
- New OEM Mazda fuel filter
- Denso IK22 Iridium spark plugs for Rotrex/F.I.
- ITG Maxogen JC60/73 aluminum velocity stack air filter
- Hytech Racing stainless exhaust system
- SuperMiata urethane exhaust hangers
- AWR Racing engine mounts (70 durometer)
- BP6D 80 amp alternator
- Gates Racing supercharger, timing, and alternator belts
Drivetrain:
- O.S. Giken Super-Single 225mm race clutch
- ARP flywheel hardware
- MiataRoadster straight-shot clutch line
- O.S. Giken Super-Lock limited slip differential (assembled by Unitrax - official O.S. Giken assembler)
- Mazdaspeed differential housing
- Mazdaspeed driveshaft and axle set
- 4.30 final drive ratio ring and pinion gear set
- MiataRoadster Delrin differential mount kit
Cooling:
- Ron Davis cross-flow aluminum radiator
- Custom one-piece intercooler setup (minimum charge length and volume, achieving near ambient IAT's)
- Setrab 13 row engine oil cooler
- Setrab 10 row supercharger traction fluid cooler
- Mocal thermostatic oil sandwich plate
- XRP 120° -10 AN fittings (x2) - XRP 90° -10 AN fittings (x2) - Aeroquip -10 AN - M22 adapters (x4)
- Aeroquip AQP socketless oil hose
- Moroso coolant overflow tank
- Moroso oil catch can/breather tank with -6 AN line
- HPS coolant hoses
- Stant Racing high pressure radiator cap
- Jackson Racing 160° low-temp thermostat
- Oetiker stepless self-tensioning coolant hose clamps (x8)
- Norma intercooler coupler clamps
- Thermo-tec Multi-layer heat barrier transmission tunnel insulation (cool to the touch even after a full-tilt track session)
Suspension:
- 949 Racing XIDA Clubsport monotube dampers with 550F/350R spring rates and helper springs
- AWR Racing Delrin control arm bushings
- SuperMiata endlinks
- Beatrush PPF/differential brace
- New OEM Mazda wheel bearings (x4), tie rods/tie rod ends (x2), and alignment bolts (x8)
Brakes:
- Carbotech Racing pads XP12 Front / XP10 Rear
- Centric Rotors F/R
- Stoptech stainless brake lines F/R
- Wilwood proportioning valve
- Project Mu Racing brake fluid
- New Mazda pad hardware F/R
- Custom brake hard lines
Wheels/Tires:
- PANASPORT C8 13x9 3-piece racing wheels (4.4kg each!)
- Four sets of Hankook Ventus F200 C90 compound 210/570/13 racing slicks - Custom machined hub-centric wheel spacers
- ARP extended wheel studs
- 949 Racing lug nuts (machined finish)
Safety/Cockpit/Controls:
- Kirkey Racing 58 series aluminum racing seats (professionally mirror polished, pad set included)
- G-Force 5 point harnesses
- MiataRoadster medium length slim short shifter kit
- Tech Toy Tuning JGTC shift knob
- Custom machined wheel hub
- NRG quick release
- I-O port back braces
Miscellaneous:
- Odyssey PC680 Racing battery and powdercoated mounting case
- Pegasus "Afterburner" LED high-visibility brake light
- Joe's Racing aluminum side mirrors
- Project-G oil filler cap
- Project-G oil dipstick pull
- Mazdaspeed ignition wires
- Powdercoated black fine texture valve cover
- Chrome valve cover bolts
Maintenance/New:
- Water pump and gaskets
- Idler and tensioner pulleys
- F/R crankshaft main seals
- Camshaft seals
- Valve cover gasket
- Hoses and vacuum lines
- Pilot and throw out bearings
- Motul 300V 5W40 engine oil
- Motul Gear 300 75W90 transmission fluid
- O.S. Giken 80W250 limited slip fluid
